RC Circuit

CLAIMED BY MARK RUSSELL SPRING 2016

The Main Idea

An RC circuit is a circuit that contains a battery with a known emf, a resistor (R), and a capacitor (C). An RC circuit can be in either series or parallel. The figure in the top right of the page shows an RC circuit. The capacitor stores electric charge (Q)

RC Circuits use a DC (direct current) voltage source and the capacitor is uncharged at its initial state. In the figure below, you see an RC circuit with a switch. When the switch is closed, the capacitor will begin to charge as the current can now flow throughout the circuit. To discharge the capacitor, you simply disconnect the switch.

Remember that potential difference across the capacitor is delta [math]\displaystyle{ {V} = {Q}/{C}\lt math\gt , where Q is charge on the plate and C is the capacitance. When the switch is closed, voltage on the capacitor rises rapidly at first, due to the high current at time = 0. The voltage opposes the battery, increasing from zero to the max emf when the capacitor is fully charged. The current decreases from its initial value of \lt math\gt {I}_{0} = {emf}/{R}\lt math\gt to 0 as the voltage on the capacitor reaches the same value as the emf. The current is initially at its max at time t=0. Once the potential difference across the plates of the capacitor equals the battery's voltage supply, current will stop flowing through the circuit. This is known as the steady state of an RC circuit; it is reached when time goes to infinity. Kirchhoff’s loop rule explains that the sum of changes in potential around any closed loop must be zero. The equation for voltage versus time when the capacitor is charged through resistor R is \lt math\gt {V} = {emf(1-e^{\frac{-t}{RC}})} }[/math] V is defined as the voltage across the capacitor. Emf is equal to the emf of the dC voltage source. The units of RC are in seconds. Tau= RC. Tau is the constant of time in the RC circuit. The smaller the resistance, the faster a capacitor will be charged. It takes longer to charge than to discharge. This is because a larger current flows through a smaller resistance (I=V/R). Also the smaller the capacitor (C), the less time it will need to charge. Tau = RC explains both of these.

A Mathematical Model

ΔV = I * R

Q=CV

Node Rule-Current is assigned (positive or negative) quantity reflecting direction towards or away from a node. This principle can be solved by adding all the currents up to equal 0. The Node Rule is important to RC Circuits because finding the current flow in the different states of an RC Circuit often relies on nodes when the capacitor is in parallel.

Loop Rule-Similar to the node rule; however, the voltage jumps and drops are added up around the circuit to equal to 0.

Examples

Simple

In the steady state what is the potential difference across the plates of the capacitor? The circuit has a resistor, R, capacitor, C, and battery, Vs.

Solution: The key concept in this problem is that in the steady state time is approaching infinity. In an RC circuit as time approaches infinity, the current is 0 because the potential difference across the capacitor equals that of the battery. Therefore, the potential difference across the plates of the capacitor equals Vs.

Difficult

The circuit below has been in position a for a long time. At time t = 0 the switch is thrown to position b. DATA: Vb = 12 V, C = 10 mF, R = 20 W

a.) What is the current through the resistor just BEFORE the switch is thrown?

The circuit is in a steady state so I = 0

b.) What is the current through the resistor just AFTER the switch is thrown?

Solution: I = V/R I = 0.6 amps since the capacitor has a potential difference and is creating the current.

c.) What is the charge across the capacitor just BEFORE the switch is thrown?

Solution: Q = CV Q = 120 mC

d.) What is the charge on the capacitor just AFTER the switch is thrown?

Solution: Charge does not change instantaneously Q = 120mC

Connectedness

1. How is this topic connected to something that you are interested in?

RC Circuits can be used in musical instruments such as guitars and amplifiers. I play the guitar so it is cool to see how the guitar actually works.

1. How is it connected to your major?

Mechanical Engineering requires the use of many electronics and learning how various circuits work is necessary for creating new parts and machines.

1. Is there an interesting industrial application?

RC circuits can be used in many industrial areas to allow certain frequencies to pass through a circuit.

See also

Further reading

Charge in a RC Circuit

Current in a RC circuit

Loop Rule

Node Rule

Current

External links

http://hyperphysics.phy-astr.gsu.edu/hbase/electric/rcimp.html

http://www.allaboutcircuits.com/textbook/alternating-current/chpt-4/series-resistor-capacitor-circuits/

References

http://www.electronics-tutorials.ws/rc/rc_1.html

https://www.pa.msu.edu/courses/1997spring/PHY232/lectures/kirchoff/examples.html