Conductivity

Claimed by Patrick Todd (Spring 2017)

Definition

Conductivity is the degree to which a specified material conducts electricity, calculated as the ratio of the current density in the material to the electric field that causes the flow of current. (It is the reciprocal of the resistivity.)

In other words, Conductivity is the measure of the ease at which an electric charge or heat can pass through a material. Electrical conductivity tells us how well a material will allow electricity to travel through it. Thermal conductivity tells us the ease upon which thermal energy (heat for most purposes) can move through a material.

Symbols

Electrical Resistivity is mainly represented by the Greek lower-case rho. Electrical Conductivity is mainly represented by the Greek lower-case sigma, but is occasionally represented by a lower-case kappa, or gamma.

SI Units

Electrical Resistivity is measured in Ohm-Metres. Electrical Conductivity is measured in Siemens per Metre

Classification of Materials by Conductivity

Conductors, Semiconductors, and Insulators are the main three classifications of a material when talking about its electrical conductivity. Conductors are materials with high conductivity. Semiconductors have an in between level of conductivity, while insulators have low conductivity. Meaning if you want to pass a lot of electricity to something use a conductor, if you want to pass some electricity but also lower the original amount use a semiconductor, and if you want to cut the flow of electricity use an insulator. Provided below is a list of materials that fit into each category.--Rwilliams354 (talk) 14:53, 27 November 2016 (EST)

         Conductors: Gold, Iron, Silver, Copper, Aluminum, Tin
         Semiconductors: Silicon,  Germanium
         Insulators: Glass, Porcelain, Rubber, Cloth, Paper, Air

Semiconductors

Semiconductors are materials that have a conductivity in-between that of an insulator and a conductor. However, as temperature increases, unlike in most metals, the conductivity of semiconductors increases.

Temperature Dependence

As temperature increases, the electrical resistivity of metals increases. This is a reason why when computers heat up, they tend to slow down. Some materials exhibit superconductivity at extremely low temperatures. Below a certain temperature, resistivity vanishes, such as Pb at 7.20 K.

Equations

Maxwell's Equation for Electric Conductivity'--Rwilliams354 (talk) 14:13, 27 November 2016 (EST)

J=(conductivity)E --Rwilliams354 (talk) 14:13, 27 November 2016 (EST)

          J= Electric Current Density
          E= Electric Field

Electric current density can be thought of as the electric current per cross sectional area of a specific material. Therefore this formula relates to each material differently. Every material has a specific conductivity associated with it, and this conductivity can help describe the electric field in each material. For example, materials such as copper and silver have extremely high electric conductivity and therefore in order to not have an almost infinite electric current density we can approximate the electric field inside the metals to be zero. This equation is essentially the proof for all metals having a zero electric field on the inside. --Rwilliams354 (talk) 14:13, 27 November 2016 (EST)

Poulliet's Law

R=ρℓ/A

          R = Electric Resistance
          ρ = Electric Resistivity
          ℓ = Length
          A = Cross-Sectional Area

Poulliet's Law states that a given materials resistance will increase in length, while it will decrease with an increase in Area.

Conductivity in Real Life

Conductors are used to carry electricity, as well as electrical signals in circuits. Complementary metal–oxide–semiconductors, or CMOS for short, are the foundational building block of gate based logic circuits, that make up the majority of all modern electronics. CMOS circuits are composed of a combination of p-type and n-type semiconductors. These semiconductors will change their conductivity, based on the applied voltage, allowing for logic of 0's and 1's, or low voltage and high voltage, to be transferred through logical circuits. This allows us to apply boolean logic to circuits, such as AND and OR logic, or even create an amalgamation of AND's and OR's to create electronics, such as multiplexors, switches, latches, registers, decoders, encoders, etc.

https://www.youtube.com/watch?v=ODbgKXFED5o--Rwilliams354 (talk) 14:13, 27 November 2016 (EST)

History

Stephen Gray, Father of Conduction--Rwilliams354 (talk) 14:15, 27 November 2016 (EST)

Born 1666 in Canterbury, England. Died 1736 in London, England.--Rwilliams354 (talk) 14:15, 27 November 2016 (EST)

Gray was an innovative thinker who performed many a experiment including work with the transmission of electricity. One day while performing one of his experiments, unbeknownst to him he discovered the difference between insulators and conductors. He was working with transmitting electricity and he changed the transmission wire from silk to brass wire when he noticed that electricity passes completely different in brass than it does in silk. After said discovery, Gray spend the next 3 years with the help of friends and family doing more research in similar topics, and with this research some might say solidified his name as the father of conduction.--Rwilliams354 (talk) 14:15, 27 November 2016 (EST)

External links

Beginner Explanation

References

History: "Gray, Stephen." Complete Dictionary of Scientific Biography. . Encyclopedia.com. 25 Nov. 2016 <http://www.encyclopedia.com>.--Rwilliams354 (talk) 14:13, 27 November 2016 (EST)

Equations: "Conductivity." Maxwells-Equations.com, 2012. http://maxwells-equations.com/materials/conductivity.php --Rwilliams354 (talk) 14:10, 27 November 2016 (EST)